vicmarc-catalogue

Chucks

For Chucks inserts please go to Chucks Inserts page

VM90

vm90_small

VM90 Std Jaws Thread Size
V00281-4 M40 X 2 ( Insert Required )
V00281-2 M33 X 3.5 ( Direct Thread )

The VM 90 STD Jaws comes with: 1 x Standard Jaws, 1 x 3mm T– Bar Allen Key, 1 x Wood Screw, 1 x Users Manual, 2 x 7.9mm (5/16”) Tommy Bars, Please note the M40 x 2 chuck, an insert is required (not included)

VM90 No Jaws Thread Size
V00280-4 M40 X 2 ( Insert Required )
V00280-2 M33 X 3.5 ( Direct Thread )

The VM 90 No Jaws comes with: 1 x 3mm T– Bar Allen Key, 1 x Users Manual, 2 x 7.9mm (5/16”) Tommy Bars,

Please note the M40 x 2 chuck, an insert is required (not included)

VM100

VM100_chuck

VM 100 STD Jaws Thread Size
V00283-4 M40 X 2 ( Insert Required )
V00283-2 M33 X 3.5 ( Direct Thread )

The VM 100 STD Jaws comes with: 1 x Standard Jaws, 1 x 3mm T–Bar Allen Key, 1 x 8mm T–Bar Allen Key, 1 x Wood Screw, 1 x Users Manual, Please not, 1 x 7.9mm (5/16”) Tommy Bar (M40 Only), M40 x 2 chuck, an insert is required (not included)

VM 100 No Jaws Thread Size
V00282-4 M40 X 2 ( Insert Required )
V00282-2 M33 X 3.5 ( Direct Thread )

The VM 100 No Jaws comes with: 1 x 3mm T–Bar Allen Key, 1 x 8mm T–Bar Allen Key, 1 x Users Manual, Please note, 1 x 7.9mm (5/16”) Tommy Bar (M40 Only), M40 x 2 chuck, an insert is required (not included)

VM120

4-Jaw-FrontCMYK-2

VM 120 STD Jaws Thread Size
V00285-4 M45 x 2 ( Insert Required )
V00285-2 M33 X 3.5 ( Direct Thread )

The VM 120 comes with: 1 x Standard Jaws, 1 x 4mm T–Bar Allen Key, 1 x 10mm T–Bar Allen Key, 1 x Wood Screw, 1 x Users Manual, Please note, 1 x 9.5mm (3/8”) Tommy Bar (M45 Only), M45 x 2 chuck, an insert is required (not included)

VM 120 No Jaws Thread Size
V00284-4 M45 x 2 ( Insert Required )
V00284-2 M33 X 3.5 ( Direct Thread )

The VM 120 No Jaws comes with: 1 x 4mm T–Bar Allen Key, 1 x 10mm T–Bar Allen Key, 1 x Users Manual, Please note, 1 x 9.5mm (3/8”) Tommy Bar (M45 Only), M45 x 2 chuck, an insert is required (not included)

VM150

4-Jaw-FrontCMYK-2

VM 120 STD Jaws Thread Size
V00285-4 M45 x 2 ( Insert Required )
V00285-2 M33 X 3.5 ( Direct Thread )

The VM 120 comes with: 1 x Standard Jaws, 1 x 4mm T–Bar Allen Key, 1 x 10mm T–Bar Allen Key, 1 x Wood Screw, 1 x Users Manual, Please note, 1 x 9.5mm (3/8”) Tommy Bar (M45 Only), M45 x 2 chuck, an insert is required (not included)

VM 120 No Jaws Thread Size
V00284-4 M45 x 2 ( Insert Required )
V00284-2 M33 X 3.5 ( Direct Thread )

The VM 120 No Jaws comes with: 1 x 4mm T–Bar Allen Key, 1 x 10mm T–Bar Allen Key, 1 x Users Manual, Please note, 1 x 9.5mm (3/8”) Tommy Bar (M45 Only), M45 x 2 chuck, an insert is required (not included)

Escoulen Chucks (Eccentric Chucks)

Escoulen Chuck #3 Thread size
V00295-2 M33 x3.5
V00295-5 (insert required) M45 x 2

It is supplied with a set of standard accessories, 1 x Tommy bar 7.9mm, 1 x 5mm Allen T-Bar, 1 x 4mm Allen T-Bar, 1 x 4mm Allen L-Bar, 1 x #3 Gauge, 1 x 10mm spanner, 1 x 40mm Cup Chuck, 1 x owner’s manual.

Please note that the V00295-2 chuck does not come with a chuck removal key, use your 41mm AF open end spanner supplied with all Vicmarc Lathes, if using any other lathe with the same thread size, you will need to purchase the spanner, see below.

The V00295-5 chuck does not require the spanner as it’s held onto the lathe by the insert which has a hole drilled in it and a Tommy bar supplied.

Open end spanner 41 AF, order code V01035

eccentric

VICMARC PEN BLANK CHUCK

VICMARC PEN BLANK CHUCK

Drill a perfectly centered hole in your blank on your lathe using this unique lathe chuck. The chuck includes two jaws that will hold your blanks perfectly centered at the headstock. Mount a drill chuck with your drill bit into your tailstock and advance the drill into your blank as it spins on your lathe. Advantages of this system:

  • Instant set up and perfect centering
  • No “travel” limitations of a drill press quill
  • Will open from 8 – 25mm across flats.
  • Comes with 1 x 8mm Tommy Bar

Please note: for insert type chuck, an appropriate insert to fit your lathe is required.

Thread Size Part No.
M30 x 3.5 V00279-1
M33 x 3.5 V00279-2
1 1/4″ x 8 V00279-3
1” x 8 V00279-6
1” x 10 V00279-7
3/4” x 16 V00279-8
M40 x 2 (requires a Chuck Insert) V00279-4
vicmarc-catalogue